BORNNET.COM

mm.	CLOSEST
150	ASTM	TYLER	BSS
	E2282		41062
4.75	4	4	3/16 INCH


4.00	5	5



3.35	6	6	5

3.00
2.80	7	7	6


2.36	8	8	7
2.00	10	9	8

1.70	12	10	10
1.40	14	12	12
1.18	16	14	14
1.00	18	16	16
0.85	20	20	18
0.71	25	24	22
0.60	30	28	25
0.50	35	32	30
0.42	40	35	36
0.35	45	42	44
0.30	50	48	52
0.21	70	65	72
0.15	100	100	100
0.075	200	200	200
0.045	325	325	350

Application	CHEMICAL ANALYSIS % BY WT.
Calcium Hypochlorite is a source of highly concentrated chlorine suitable for use in the chlorine released is highly effective in combating microoganisms of all kinds, making it suitable for the following applications : - chlorination of drinking water. - treatment of swimming pool water. - treatment of seawage disposal. - bleaching of natural fibers. - as a disinfectant and deodorizing agent in sanitary applications, floor cleaner etc.	CALCIUM HYPOCHLORITE	65 min.
	INERT MATERIALS	35 max.
	WATER	0.8 max.
	TOTAL HEAVY METAL OXIDES	0.2 max.
	PHYSICAL PROPERTIES	-
	MOLECULAR WT.	142.99
	BLUK DENSITY	0.8 - 0.9 g./ml
	pH OF 10g./1 SOLUTION	9.5
	SOLUBILITY IN WATER	216 g./1at 25°
	APPEARANCE	WHITE FINE GRANULE

Preparing calcium hypochlorite solution	Storage :
1. Use a clean, non-metallic container free of grease, oil or residue. 2. Add granular calcium hypochlorite to lukewarm water. 3. Slur for tree to five minutes. 4. Use immediately. Note : As a safety precaution, prepare only the amount of solution needed. Nver store a calcium hypochlorite solution.	Storage in cool, dry, well ventilated place, away from sources of heat, flames, sparks combustible liquids or solids, kerosene, acids, paints, oils and organic materials. Keep container closed when not in use.
	Packing :
	50 kgs. plastic drum.

DESCALER
GENERAL DESCRIPTION	APPLICATION
Calces Eradication - 111 is a highly effective scale and deposit remover based on acid solution form. This products is treated by acid inhibirror to prevent corrosion cracking on stainless stell and metals.	Calces Eradication is normally dilute up to 30 - 40% depending on amout of deposit to be removed. The product can work at normal temperature. For higher temperature between 50 - 60%C ferther information should be suggested to enhance higher effectiveness. Your V.S.T.C. specialist will recommend the optimum dosage and the exact method of application.
TYPICAL PROPERTIES	PACKING
Appearance : Brown liquid pH : Less than 1 Flammability : None	20 Kgs.

*Application*		*Feeding*
Calces Protection - 112 is a total organic colling watertreatment which controls scales, corrosion and prevents the deposition of materials the retard heat transfer.		Calces Protection - 112 may be pumped directly from the drum into a recirculating cooling water line or the tower basin. Pumping may be on a continuous bleed off to maintain the recommended cycles concentration The preferred method is to use an automatic dosing system which operates proportional to system loading and conserves both water and treatment.
*Advantage*		*Dosage*
* Complete single treatment * Minimal disposal problems * Maintain clean systems * Inhibit scale and corrosion		For best results, pre-treat new or existing systems with between three and five times the normal maintenance dosage for seven to ten days. The maintenance dosage of Calces Protection - 112 should than be maintained in the recirculating water at all times. Your V.S. Treatment consultant will advise you with regard to the specific dosage requirements for your system.
*Physical Properties*		*Available Packaging*
Appearance Color Specific Gravity pH	: Liquid : Colorless : 1.1 (25º C) : 6.7 (approx)	20 Kgs/drum

TRADE NAME :	LICHEN PROTECTION
QUALIFICATION :	Lichen Protection - 113 is a highly effective controller growing of lichen, bacteria, mold and algae.
INGREDIENTS :	(1) 5 - chloro - 2 methy1- 4isothaizolin-3-one (cas no.26172-55-4) (2) 2-methy1-4-isothaizolin-3-one (cas no. 2682-20-4) (3) Magnesium nitrate (cas no.10377-60-3) (4) Magnesium Chloride (cas no. 7886-30-3) (5) Cupric nitrate

Date : 08/01/02			Lot No. : 20102
			Production Date : 07/01/02
		Spec.	Actual Result
1. Aluminium Oxide (Al₂O₃)	%	10.0 - 11.0	10.14
2. Basicity	%	45.0 - 65.0	50.08
3. pH	( at 1 % wt./v)	3.5 - 5.0	4.05
4. Specific Gravity	( g./cc., at 25° C)	1.19 min	1.21
5. Sulface ion (SO₄²)	%	3.5 max.	2.17
Remark : Durability (at room temp.) 3 months

PROPERTY AND USE
PAC is a SO²₄ modified product of polyaluminum chloride. It is yellow flake slightly deliiquescscent (be stored tightly) , water soluble with slight acidity (pH 3.5 - 5.0). It can reduce remarkably the turbidity of water and remove the harmful substances in water to a great extent. PAC is used mainly in purifying industrial water and in treating waste water whose efficiency is higher than basic aluminum chluminum chloride by 2 times and higher than aluminum sulfate by 6 - 8 times. Its quality has been appraised to be of low dosage, of high efficiency of flocculation and of adaptability.
S P E C I F I C A T I O N
Matter of water unsoluble	1 %
As	10 ppm.
Cr	12 ppm.
Hg	0.6 ppm.
Pb	14 ppm.
Cd	6 ppm.
Al₂O₃	30.0 %
Basicty	50.0 - 85.0 %
PH value ( 1 % W/V)	3.5 - 5.0
INSTRUCTION
Dissolve 1 part PAC in 100 part ( by weight) water giving a homogeneous, solution, then add this solution into the water to be purified with stirring. After addition continue tostir for precipitation and filter to get the qualified water.
DOSAGE
In order to meet the different requirement of water quality the dosage should be determined first in the laboraatory. In general, the dosage is : 1. 1 - 10 g./ton for industrial water. 2. 10 - 200 g./ton for waste water.
PACKING : 25 Kgs.

*Description*
FLOCTEX 2705 is a high molecular weight, medium charge anionic polymer are used to increase the efficiency of setting, clarfication, sludge thickening and sludge de-watering. This product is approved for use by the EPA in the clarification treatment of raw water for potable usage.
Application Primary Clariflication
To increase the removal of suspended solid aand BOD. Biological clarification FLOCTEX 2705 may be requied to provide either improved settling rates or suspended solids capture.
*Sludge thickening*
FLOCTEX 2705 is used in sludge thickening. As waste sludge very broadly in make up, extensive testing may be required to choose the optimum product.
*Available Packaging*
25 kg/bag
Sludge de-watering
This is often the most demanding polymer application. Due to the high polymer demand and difficulty in removing the maximum amout of water, proper polymer selection is critical. In all cases, floc development and de-watering rate must be evaluated.
*Plant feed solution preparation*
Viscosity will limit the practical solution strengths of the dry polymers. The following are the maximum recommended strengths. Solution may be prepared manually by using a low speed mixer with relatively large blades must be used to mix the polymer in the tank. Product degradation will occur if high speed mixers are used. Approximately 30 minutes of mixing is required to properly prepare a feed solution. The mixer should then be turned off.
*Typical Characteristic*
Appearance	White powder
Approximate Bulk density	0.8
Recommended operating concentration ( g/l )	3
Maximum operating concentration ( g/l )	5
Approximate Brookfield viscosity ( cps ) ( 1 g/l )	200
Dissolution time in DI water 5 g/l 25°C (minutes)	30-60
Storage temperature ( °C )	0-35
Shelf life (months)	24

F L O C T E X 2 7 0 6 ............ P R O D U C T B U L L E T I N ................. W A C H E M P e r f o r m a n c e C h e m i c a l s

*Description*
FLOCTEX 2706 is a high molecular weight, high charge anionic polymer are used to increase the efficiency of setting clarification, sludge thickening and sludge de-watering. This product is approval for use by the EPA in the clarification treatment of raw water for potable usage.
Application Primary Clariflication
To increase the removal of suspended solid and BOD. Biological clarification
FLOCTEX 2706 may be required to provide either improved setting rates or suspended solids capture.
*Sludge thickening*
FLOCTEX 2706 is used in sludge thickening. As waste sludge very broadly in make up, extensive testing may be required to choose the optimum product.
*Available Packaging*
25 kg/bag
Sludge de-watering
This is often the most demanding polymer application. Due to the high polymer demand and difficulty in removing the maximum amout of water, proper polymer selection is critical. In all cases, floc development and de-watering rate must be evaluated.
*Plant feed solution preparation*
Viscosity will limit the practical solution strengths of the dry polymers. The following are the maximum recommended strengths. Solution may be prepared manually by using a low speed mixer with relatively large blades must be used to mix the polymer in the tank. Product degradation will occur if high speed mixers are used. Approximately 30 minutes of mixing is required to properly prepare a feed solution. The mixer should then be turned off.
*Typical Characteristic*
Bulk density	( approx.) 0.08
Recommended operating concentration ( g/l )	3
Maximum operating concentration ( g/l )	5
Dissolution time in DI water 5 g/l 25°C (minutes)	30 - 60
Storage temperature ( °C )	0 - 35
Shelf life (months)	24

*Description*
FLOCTEX 2709 is a high molecular weight, high charge anionic polymer are used to increase the efficiency of setting clarification, sludge thickening and sludge de-watering. This product is approval for use by the EPA in the clarification treatment of raw water for potable usage.
Application Primary Clariflication
To increase the removal of suspended solid and BOD. Biological clarification
FLOCTEX 2709 may be required to provide either improved setting rates or suspended solids capture.
*Sludge thickening*
FLOCTEX 2709 is used in sludge thickening. As waste sludge very broadly in make up, extensive testing may be required to choose the optimum product.
*Available Packaging*
25 kg/bag
Sludge de-watering
This is often the most demanding polymer application. Due to the high polymer demand and difficulty in removing the maximum amout of water, proper polymer selection is critical. In all cases, floc development and de-watering rate must be evaluated.
*Plant feed solution preparation*
Viscosity will limit the practical solution strengths of the dry polymers. The following are the maximum recommended strengths. Solution may be prepared manually by using a low speed mixer with relatively large blades must be used to mix the polymer in the tank. Product degradation will occur if high speed mixers are used. Approximately 30 minutes of mixing is required to properly prepare a feed solution. The mixer should then be turned off.
*Typical Characteristic*
Appearance	White powder
Approximate Bulk density	0.8
Recommended operating concentration ( g/l )	3
Maximum operating concentration ( g/l )	5
Approximate Brookfield viscosity ( cps ) ( 1 g/l )	300
Dissolution time in DI water 5 g/l 25°C (minutes)	30 - 60
Storage temperature ( °C )	0 - 35
Shelf life (months)	24

*Description*
FLOCTEX 3808 is a high molecular weight, high charge anionic polymer are used to increase the efficiency of setting clarification, sludge thickening and sludge de-watering. This product is approval for use by the EPA in the clarification treatment of raw water for potable usage.
Application Primary Clariflication
To increase the removal of suspended solid and BOD. Biological clarification
FLOCTEX 3808 may be required to provide either improved setting rates or suspended solids capture.
*Sludge thickening*
FLOCTEX 3808 is used in sludge thickening. As waste sludge very broadly in make up, extensive testing may be required to choose the optimum product.
*Available Packaging*
25 kg/bag
Sludge de-watering
This is often the most demanding polymer application. Due to the high polymer demand and difficulty in removing the maximum amout of water, proper polymer selection is critical. In all cases, floc development and de-watering rate must be evaluated.
*Plant feed solution preparation*
Viscosity will limit the practical solution strengths of the dry polymers. The following are the maximum recommended strengths. Solution may be prepared manually by using a low speed mixer with relatively large blades must be used to mix the polymer in the tank. Product degradation will occur if high speed mixers are used. Approximately 30 minutes of mixing is required to properly prepare a feed solution. The mixer should then be turned off.
*Typical Characteristic*
Appearance	White powder
Approximate Bulk density	0.8
Recommended operating concentration ( g/l )	3
Maximum operating concentration ( g/l )	5
Approximate Brookfield viscosity ( cps ) ( 1 g/l )	100
Dissolution time in DI water 5 g/l 25°C (minutes)	30 - 60
Storage temperature ( °C )	0 - 35
Shelf life (months)	24

	TRADE NAME : Hi-Chlor
	CHEMICAL NAME : Sodium Hypochlorite
	CHEMICAL FORMULA : NaOCl

ITEM	UNIT	SPECIFICATION
Available Chlorine	%	10 ± 2 %
Heat stability	%	7.7
Free Alkali as NaOH	%	105 max.

APPLICATION

Sodium Hypochlorite is used as Bleaching agent in the dyeing, pulp and paper industries and also used as bactericide and fungicide , particularly for swimming pools, deodorizer for swimming pools deodorizer for waste matters, sanitary agent for toilet and as an oxidizing agent for rubber product.

STORAGE CONDITION

* Store in a cool , dry , well-ventilated area , out of direct sunlight.
* Store away from heat and in compatible materials such as reducing materials , strong acids nitrogen compounds.

STANDARD PACKAGING

Tank car , 20 Kgs / Drum

FORMULAR :	*Na₃PO₄ 12H₂O**
MOLECULAR WEIGHT :	380.1
APPEARANCE :	White Crystal

DESCRIPTION : Specific gravity is 1.62 at 20° C. Decomposed at 73.3 - 76.7 ° C. Soluble in water to form strong alkall solution. Insoluble in ethanol and carbon disulfide. All H2O will be lost when hemted to 100° C and all H₂O will be lost when heated to 212°C.

PACKING : In polyethylene woven bags ined with polyethylene bags of 25 Kgs. net each.


*Na₃PO₄ 12H₂O**	%	98
P₂O₅	%	18.30
SO₂	%	0.50
Cl	%	0.30
Insolubles	%	0.10
Alkalinity of Methy	--	16.0 - 19.0
Whiteness	--	Above 75

CHARACTERISTICS	UNIT	SPECIFICATION
Al₂O₃ Content	% wt	16.0 Min.
pH 5% solution at 28°C	-----	2.8
Insoluble matter in water	% wt	0.3 Max.
Fe	% wt	0.1 Max

PROPERTIES	SPECIFICATIONS	TEST METHOD
Purity of Ca (OH)₂	90.0% min.	ASTM C-25
Free Lime	1.0% max	Calculated From ASTM C-25
Particle Size on 100 Mesh	0.0%	ASTM C-110
Particle Size on 170 Mesh	2.0%	ASTM C-110
Particle Size on 325 Mesh	10.0% max.	ASTM C-110
Moisture Content	1.0% max.	Manual KOHAUS
Impurity Content	2.0% max.	ASTM C-110

CHARACTERISTICS	UNIT	SPECIFICATION
Appearance	-	Clear , Light white color liquid
Strength	% wt	98.0 Min
Specific Gravity at 26° C	-	1.825
Sulfur Dioxide	ppm	25 Max
Iron	ppm	20 Max
Ash	ppm	120 Max